Visit My Website

 

 

What are your thoughts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Setting up a bathtub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and often, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will require a helper to leave the old tub as well as set in the brand-new one. Ensure you have actually qualified on your own for the work as well as fit attempting it. Instead of working with a specialist to take control of a halfway-completed project, it is better to think about employing one before you start. Chances are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new tub in your restroom if you have actually currently purchased a new bathtub and also don't need to transform the arrangement of your previous supply of water pipelines.
Your devices and product checklist ought to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the staying water that will come from the pipes. Once the supply pipes have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The former kind needs to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Mounting the Tub

Using both wooden boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To set up faucets, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and also check all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as likewise examine the overflow outlet and also the normal outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last placement.

 

 

Getting ready for the Setup

To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.

 

 

Tiling Around the Bathtub

In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to problems with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I am just very eager about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you liked our post. Make sure you take the opportunity to promote this article if you enjoyed reading it. Thanks a lot for going through it.

Contact Us Now